You have to start with a perfectly smooth surface to end up with perfectly painted walls or woodwork. One pro tells PM that Sander would be a more fitting job title than Painter since he spends so much time pushing sandpaper. Sanding levels outs spackle or joint-compound patches and flattens ridges around nail holes. Sanding also removes burrs and rough spots in your trim.
The only time it's acceptable to mix water in the paint is when you're using a deep or ultra deep base paint to reduce its stickiness, which is rare with new paint technology. Dark primary colors are composed almost entirely of tint that makes it very hard to work with without adding water. (You never use a sprayer and need to thin paint.?) If i was still in the industry I'd take the time to make a better article than this. Take this for a grain of slat. Use a reputable painter or someone you know you can trust or has been referred to you by someone you trust. I wouldn't hire anyone I had to watch like a hawk to make sure they're not screwing me.
Most painters have no problem painting doors in place, but they recommend you lay the door on sawhorses and work horizontally. If you have a paneled door, start with the panels and work from the outside edges in toward the center. "Watch the corners — paint loves to puddle," warns Dixon. While the paint is still wet, lightly "tip off" the panel with an almost dry brush. (Tipping off is pulling the brush over the surface to level out the finish.) When painting the stiles (vertical) and rails (horizontal) just follow the grain of the wood. When the grain changes abruptly, for instance, where the rail meets the stile, don't stop your brush stroke — you'll only leave a lump of paint. Apply paint across the joint with a full stroke, and then tip off the overlapping section by pulling the brush in the direction of the grain. "Make sure the door is dry before painting the opposite side or rehanging it," says Maceyunas.
Basic labor to paint home with favorable site conditions. Prep up to 3 hr per 100 SF - clean, scrape, sand and patch up to 4 defects per 100 SF. Caulk gaps and spot prime. Roll / brush 2 coats of paint over lightly textured ceiling/walls. Paint up to 2 doors and door trim per room. Includes planning, equipment and material acquisition, area preparation and protection, setup and cleanup. 129 square feet $93.64 $126.68
Back to the article. You can add water to all latex based paints / thinner to oil based paint. The tinting base has absolutely nothing to do with it. Say you are working outside and throughout the day you have to add a little water to keep the same consistency. If somebody really tried to add 20% to 50% water they no longer would be painting they'd be performing a whitewash or pickle finish.
Did you even read the article? It was specifying UNSCRUPULOUS painters! And, by the way, the photo at the top was not identified at all. How would anyone know whether it was done by a homeowner or not? Also did you ever stop to think that if a consumer has the knowlege to spot a dishonest contractor then by default he also has the knowlege to identify an honest one as well? And, pardon me, but just because you've never seen something has absolutely nothing to do with whether it has actually happened to someone else. Why would any honest business person be so defensive about the publishing of such useful information? If any painters/painting contractors object to a consumer having this kind of information maybe they are the dishonest ones!
Unless you like textured walls, don't paint over dust. Wash the walls with trisodium phosphate (TSP) or a mild cleaner, like Jasco's TSP No-Rinse Substitute. For smoke-stained walls, Toto uses a 50/50 solution of bleach and water. To clean a wall, use two buckets. Load up your rag or sponge from your cleaning-solution bucket, and scrub. Before redipping, rinse the sponge in a second bucket filled with clean water.
If you decide to paint multiple rooms in your home, choose colors that relate to one another without being completely the same -- unless uniformity is your goal, of course. Costs may vary based on differences in color, gloss and room size. However, each room will flow depending on the trim's color -- which should all be white or neutral -- so they look connected. A whole-house color scheme presents the same cost factors as painting multiple rooms individually: colors you choose, the gloss, the size of the rooms and time/labor. You can choose to use the same color throughout your entire home to save on money, or you can use a color scheme with the same gloss throughout, though this isn't recommended for selling purposes.
If you're done painting for the day but still have more to do tomorrow, you don't have to go through the laborious process of cleaning your paintbrushes and paint-roller sleeves. Instead, simply brush or roll off the excess paint, then tightly wrap them in plastic food wrap. If necessary, double up the plastic to seal out any air, then place the wrapped brushes and roller sleeves in the refrigerator to keep them fresh. This might sound crazy, but it works—it'll keep the paint from drying overnight and rendering your equipment unusable.
Keeping our work environment clean is an important part of our process. We use Hepa filtered Festool dust-extractors as part of all our of prep and sanding, from drywall repairs to pole sanding. We also clean as we go. This means that for bigger projects that span more than one day, you get the benefit of daily clean up, contained mess and the ability to still function in your home during the project. We understand that renovations and painting can be disruptive to your home life, so we do everything we can to minimize the inconvenience for you and your family.
Most pros don't bother cleaning brushes and rollers if they are going to use them the next day on the same job. "Latex paint dries slowly in cold temperatures," says Maceyunas. For two-day jobs, he wraps the rollers and brushes in plastic grocery bags and sticks them in the refrigerator. "Just allow the roller to return to room temperature before reusing it," he says. Roller covers are almost impossible to clean thoroughly. Most pros buy new covers for each job.