When your brush is loaded with paint, it's easy to create runs by applying too much paint in corners or along trim. To avoid that, start brushing about 1/2 inch away from the cut-in area to apply the paint. As the brush unloads, move over and slowly drag the brush along the trim or corner. Let the bristles gently push the paint against the cut-in area where the walls meet. You may have to do this a couple of times to get complete coverage, but it'll avoid excess paint along woodwork and in corners.

You have to start with a perfectly smooth surface to end up with perfectly painted walls or woodwork. One pro tells PM that Sander would be a more fitting job title than Painter since he spends so much time pushing sandpaper. Sanding levels outs spackle or joint-compound patches and flattens ridges around nail holes. Sanding also removes burrs and rough spots in your trim.
The Cutters. Someone with meticulous attention to detail and a steady hand should be assigned the job of "cutting in," or painting a straight edge where needed, such as along a wall where the ceiling does not get painted. Many products are available to assist, but none work as well as a person who's good at doing it freehand. Ensure this person is skilled (ask them to show you). A poor, jagged, wavy or splotched cutting-in job will jump out at you every time you walk by it. Why more than one cutter? This job is nerve-wracking and painful to hands and arms after a few days. You'll want to give this person a break after a few walls.
A textured wall will need more paint than a smooth wall. The texture adds more surface area, even though it doesn't increase square footage. Determining the additional surface area depends on how much texture there is. Painters will probably estimate about 300 to 350 additional square feet of paint to account for texture. Factor additional surface area into your square footage calculations when seeking professional estimates.
An easy way to calculate the square footage of a room, is to measure and add the total length of the all the walls, then multiplying that total by the height of the room. If there are big areas within that space that are not getting painted, it’s a good idea to deduct their square footage from the total. Examples are: a large window wall, double doors, or a wallpapered wall. If two coats are required, the measured square footage is doubled. In a 10 by 14 room the walls have a linear length of 48 feet. Multiplying 48 times 8 (the height of the walls) will give us 384 square feet of paintable wall.
DON"T EVER PAINT THE WALLS TO FRESHEN UP YOUR HOME & NEGLECT THE TRIM, MOULDING & DOORS DO NOT HIRE PEOPLE BASED ON THEIR WORD ALONE, IN THESE TIMES IT IS NOT ENOUGH. DON'T AGREE TO PAY HOURLY NOR HALF UPFRONT...FOR PAINT ETC..LOL OR THEY MAY NEVER SHOW UP AGAIN. IF A COMPANY ASK HOW MANY EMPLOYESS WILL BE PAINTING THE HOUSE SO YOU CAN GET A MORE ACCURATE TIME FRAME TO COMPLETE JOB. NOW I NEED TO HIRE SOMEONE TO CLEAN UP A FRIEND OF A FRIEND'S MESS WORK WAS SUBPAR. ALWAYS ASK TO SEE LICENSE AS ALOT OF THOSE I INTERVIEWED CLAIMED ON THE PHONE TO HAVE JUST SO THEY COULD CHARGE MORE, & GAIN ACCESS . THEN THE SALEMAN SIDE COMES OUT. WHEN QUESTIONED FOR PROOF THEY THEN WANT TO NEGIOTATE PRICE. ASK IF RECALKING THE WINDOWS IS INCLUDED IN PRICE...
Just like with roller paint application, painters are not limited to using just one stroke when cutting in. It is important, however, to work towards the edge of the corners applying even pressure. If time permits, painters should allow their cut in work to dry completely before applying paint with rollers, keeping in mind that light touchups on corners and edges will always be required at the end.
Don't hesitate to ask all the questions you need to feel comfortable hiring a professional. You can also ask 3-4 professionals to make sure you have the right quote in mind. You must make sure they have a warranty or some kind of paperwork stipulating the quality of their jobs. Insurance is also a #1 priority to consider, as damage can happen in the process of painting.
An easy way to calculate the square footage of a room, is to measure and add the total length of the all the walls, then multiplying that total by the height of the room. If there are big areas within that space that are not getting painted, it’s a good idea to deduct their square footage from the total. Examples are: a large window wall, double doors, or a wallpapered wall. If two coats are required, the measured square footage is doubled. In a 10 by 14 room the walls have a linear length of 48 feet. Multiplying 48 times 8 (the height of the walls) will give us 384 square feet of paintable wall.
The price to paint an interior versus an exterior depends on a few factors. For painting an exterior, you will pay about $2,600. This is because you have to account for the siding, making sure the weather doesn't affect the job and dealing with weather conditions. On the other hand, the price to paint a home interior is around $1,700 -- less to worry about other than keeping the flooring and furniture paint-free. If you want to do both the interior and exterior, talk to the painters about any deals or their opinion on timeline and how it affects your budget.
Generally, it will take a minimum of two gallons of paint to cover a room. At the highest end, paint will cost anywhere between $30 and $60 per gallon and come in three different finishes: flat, semi-gloss or high-gloss. Flat finishes are the least shiny and are best suited for areas requiring frequent cleaning. Semi-gloss finishes are a bit shiny but can also be easily cleaned. A high-gloss finish is stain-resistant and easy to clean. Traditionally, living rooms should be painted with a flat finish to allow the paint to stand out. Glossy finishes should be reserved for hallways, and a semi-gloss is best suited for trim. Invest in pre-primed paint whenever possible. This cuts down on time by combining the layering process. Almost any paint job will require a primer, which will cost anywhere from $7 to $15 per can. Primer helps the paint to stand out against the underlayer of paint it's covering, especially if the new paint is lighter than the old coat. You will need at least two cans of primer, if not more, to cover one wall. Here are some paint brands and their average price per gallon:
If you are going to hire a contractor (professional painter) give a room by room punch list of the fixing of holes small or big, have it identified for the painter to tell you if you need a drywall finisher or if he does this type of work good. Wall repairs can be 3-5 steps to do repairs ( one per day for good drying of patching material and a good sanding) this is what gives you a good paint job only using high quality paint.
Forget the stepladder and get yourself a telescoping extension pole for your paint roller. Extension poles come in various lengths, up to 18 feet long, but one that extends from 18 to 36 inches is good enough to paint rooms with 8- to 9-foot-tall ceilings. Check that your paint roller's handle has a threaded hole in the end, then simply twist it onto the extension pole.
To pick the right color for your space, grab lots of paint chips, place them on the wall near the trim, and look at during different times of the day to see how light affect the color. When you’re ready to start testing shades, paint sample colors onto sheets of heavy paper instead of the wall so you can move them around and not make a mess of your walls. 
The problem with painting along the edge of textured ceilings is that it's almost impossible to get a straight line along the top of the wall without getting paint on the ceiling bumps. Pros have a simple solution. They run a screwdriver along the perimeter of the ceiling to scrape off the texture. "This lets you cut in without getting paint on the ceiling texture," one of our pros says. "The screwdriver creates a tiny ridge in the ceiling, so the tips of your paint bristles naturally go into it. And you'll never even notice the missing texture."
Lap marks are those ugly stripes caused by uneven layers of paint buildup. They occur when you roll over paint that’s already partly dry. (In warm, dry conditions, latex paint can begin to stiffen in less than a minute!) The key to avoiding lap marks is to maintain a “wet edge,” so each stroke of your roller overlaps the previous stroke before the paint can begin to dry.

Roger! I am so sad to hear of your retirement, but also so grateful for all the episodes you have done. I hope your health comes back to you in full force--and soon--so you can enjoy a fantastic retirement surrounded by friends and family. Your viewers will miss you greatly, but your legacy lives on in all the blooming flowers and budding gardens you've inspired over the years (including in my very own yard). I hope you'll visit the show often; we'll be looking out for you!!Sincerely,FGJ
I'm hiring an interior painter and that is why I was reading this comment list. I'm concerned about your comment about Angie's List. Some of us don't have personal recommendations for tradespersons, and rely on sites like this. Are you saying that Angie's List's reviews are not complete or that they do not print some of the negative reviews? It's hard to know what to do - I have not been able to find a person who just had their paint done so I can ask him/her about the quality of the painter.

You've got me very afraid now, I've been taken in a couple of times since I moved here. They take advantage of me because I am a single woman, not exaggerating! From gardeners to inside work. Wouldn't have house painted but I know my HOA will be after me soon, garage door is peeling and stucco needs repair. Got the $1500.00 deal, but paying more for extra work they say I need.

Sanding not only feathers out chipped paint but also provides "tooth" for the next coat of paint. For glossy trim, use a sanding sponge rather than sandpaper. Sponges mold to the shape of the trim and last longer than paper. When applying latex over alkyd paint or when he is not sure of the original finish, Brian Doherty, a painter in Richmond, Virginia, follows the hand-sanding with liquid sandpaper to make sure the surface is completely deglossed to prevent incompatibility problems. "I've seen homes where latex was used on oil-painted trim, and the paint started to peel in less than a year," says Doherty.
A fellow (actually lives in the same neighborhood) by the name of Wayne Hickey (843-655-0366) painted the ceilings and most of the walls of our house in February 2017. He got paint all over my light fixtures, all over my trim around the doors, and had visible lap marks everywhere on the walls. He came back and rectified some of the problems, but not all, as I have noticed as I have had time to look more carefully at the work he and his assistant did. His assistant had no idea (not a clue) how to roll paint on a wall or ceiling. Some places were not covered. He said he would pull nails for pictures and then re-insert the nails exactly where they were. This he did not do as he promised. He painted over the nails. His assistant had no idea how to use a paint roller. I have painted all my life, and would have done this work myself, but I just had a full knee replacement and the other knee is in bad shape. I just could not do the work. Wayne is a pleasant and congenial individual, but he can not cut in a ceiling or wall to my satisfaction - not even close. He should have a putty knife and wet cloth with him all the time to correct any paint that might get applied where it shouldn't. That is something I always did as a painter. I would not recommend Wayne to paint anybody's home.
Most of the time, the reality is different. Painting  the bulkheads around cabinets is alone more time consuming than painting an entire wall. We dread having to move the appliances and paint behind them. Moving an older fridge is like opening a Pandora’s box. Sometimes the wheels are broken and the refrigerator may damage the floor. Other times, the surfaces behind the appliances are greasy or dusty. In a small kitchen, there isn’t much room and working behind the appliances is uncomfortable. For all the reasons that were mentioned, pricing a kitchen is unpredictable.  A range of $280 to $450 should cover most possibilities.
I found Warline Paint to be honest & very professtional from start to finish. The crew arrived on time, was friendly and cleaned up afterwards. They did an excellent job of prepping and paintiing. The walls look so smooth now. I am very pleased with the results. If you want top quality work done I would highly recommend them. Thank you to Warren and his hard working crew.

Unlike sites which blend pricing from dissimilar jobs, homewyse estimates are based on the Unit Cost method. This method uses job specific detail for superior pricing accuracy and transparency - and has become an industry standard through publications and guidance of leading trade associations, including: PHCCA, the NKBA, the NECA, the AIA, and the ASPE.
Homeowners painting their home, whether it's a new coat or a new house, should ask their contractor about low-emitting paints. As the paint is applied and dries, it can release high levels of VOC's, chemicals that may be toxic to the air your family breathes (not to mention, they stink!). On top of that, these off-gassing chemicals can be absorbed by soft materials already in your home (carpet, furniture, pillow, fabric) and act as a new source to continue releasing harmful chemicals (known as "the sink effect"). There are tons of third party certified low-emitting paints on the market now for more competitive pricing and selection. You can find them listed on my organization's website at greenguard.org (those that we certify) or you can find more info from your contractor :) Happy painting!

Most painting companies, including our own, do not price our work on an hourly basis. We can work this way and do on complicated projects. But to give you a good idea of what the hourly rates tend to be, these range from $45-60 a man/hr. Then you have to factor in the cost of materials. This tends to range from 10-20% of the cost of the job depending on the level of quality.


The old adage says that you get what you pay for. With that in mind, does an expensive paint job guarantee the consumer better quality? Surprisingly, the difference in pricing does not reflect quality differences. Accurate price depends on the estimator’s business knowledge and estimating skills. The estimator of a successful painting company should know his or her “numbers”. How much a customer pays for the job is critical to the success (and often failure) of a contracting business. What is the right price for one contractor could put another out of business.
Modern Masters 1 gal. Blackened Bronze Metallic Interior Modern Masters 1 gal. Blackened Bronze Metallic Interior Paint can be used to create a high-end decorative finish in a variety of circumstances. Use it on a small accent piece or large architectural specification. Durable and long lasting for commercial application yet easy enough for do-it-yourself projects. Special formula contains ...  More + Product Details Close
Back to the article. You can add water to all latex based paints / thinner to oil based paint. The tinting base has absolutely nothing to do with it. Say you are working outside and throughout the day you have to add a little water to keep the same consistency. If somebody really tried to add 20% to 50% water they no longer would be painting they'd be performing a whitewash or pickle finish.
Want to know the color you pick will be good in your room? With this tool you can put it on some "walls" before you even paint. Here you can do it with Glidden's room visualizer tool linked below.  Either pick from our selections of rooms or upload your own and you can change walls and trim to find your perfect color. {^widget|(name)CtaButton|(Label)Paint+Your+Room+Online|(Url)https%3a%2f%2fwww.visualizecolor.com%2fglidden%23%2f|(ButtonID)Paint+Your+Room+Online|(Target)_blank|(Color)d6414d|(Edge)btn-rect|(GtmT)cta|(widget_displayname)CTA+Button^}
To paint a large section without leaving lap marks, roll the nearly dry roller in different directions along the dry edge, feathering out the paint as you go. After completing the entire length of the wall or ceiling, move to the next section and paint over the feathered edges. For the second coat, apply the paint in the opposite direction. This crisscrossing paint application sharply reduces (if not eliminates) lap marks.

Modern Masters 1 gal. Champagne Metallic Interior Paint Modern Masters 1 gal. Champagne Metallic Interior Paint can be used to create a high-end decorative finish in a variety of circumstances. Use it on a small accent piece or large architectural specification. Durable and long lasting for commercial application yet easy enough for do-it-yourself projects. Special formula contains real ...  More + Product Details Close
So sad that Angie's List requires the contractor be notified!! They have lost me as a client. If I'm dissatisfied and want to give an "F" rating (question/workers...I SHOULD NOT be intimidated into passing up an opportunity to explain my experience! There is NO WAY my contractor got an Aplus rating from over five hundred people....so someone was lying....yet I can't report that without the contractor knowing it? REALLY?
Keeping our work environment clean is an important part of our process. We use Hepa filtered Festool dust-extractors as part of all our of prep and sanding, from drywall repairs to pole sanding. We also clean as we go. This means that for bigger projects that span more than one day, you get the benefit of daily clean up, contained mess and the ability to still function in your home during the project. We understand that renovations and painting can be disruptive to your home life, so we do everything we can to minimize the inconvenience for you and your family.
Some contractors work on time and material others on a firm contract. I would never hire the former and am leary of the latter. A contractor may low-ball a bid to get the job planning to make a killing on change orders. If you say good morning to them, they charge you extra for that. If the contract is not very, very specific and extensively fleshed out or if they display their change order schedule prominently on top, show them the door.

Painting interior walls is a task better accomplished with foam rollers, because they are easy to use and can evenly cover large surface areas quickly. Foam rollers and brushes should never be overloaded with paint, as it can create drips, uneven coverage and can take longer to dry. It’s easy to get frustrated when the paint is fresh and does not look like a photo from the paint catalog, but remember: that’s something that usually happens after the second coat dries.
From beginning to end, we had an excellent experience with New Life Painting and recommend them without reservation. Noah, who represented his family business was our contact person throughout the project and was always available either directly or with a quick return of our call to answer any question. We found his initial walkthrough informative and we received New Lifeʼs exterior proposal within eight hours of his visit. The finished project is excellent. Our 1950s house has never looked so good and we are quick to tell those who have been kind enough to pay us a compliment who did our painting and landscaping.

"Dean is everything you want for a great job. He actually went to home depot twice during the replacement of a sink, range, and oven. Everything including turning the water off at the street, making sure the job was done safe and leaving the kitchen clean and operational after the install and removal of the old appliances. I highly recommend him + he's a smart and courteous veteran!"
×