Before the pros paint walls, they fill holes and patch cracks with joint compound. But if you paint directly over it, the compound will suck the moisture out of the paint, giving it a flat, dull look (a problem called "flashing"). Those spots will look noticeably different than the rest of the wall. To avoid that, pros prime the walls before painting.
"Cutting in is an acquired skill, but it's something you can't do at all with a ratty brush," says Doherty. When cutting in on a wall, he loads his brush and spreads out the excess paint, then works the brush up to the line between wall and ceiling. A brush stroke that's too wide creates a hatband, or smooth brushed band, on the very top of the wall where it meets the ceiling. To avoid this, Dixon recommends rolling first and then cutting in with a brush. "A good roller can get within 1/2 inch of the ceiling," he says. "You'll save time by not brushing more then you have to." When painting baseboards, "a wide taping knife makes a good paint guard," says Span. "Just keep the blade clean to prevent drips from working around the edge of the knife."
An empty home is less expensive as the painters don’t have to move the furniture and cover it. If the customer does not live in the house, the crews appreciate the opportunity of starting work early or finishing later. The easier scheduling and flexible timelines is a win win for both parties and and our estimator brings this to the client’s attention.
I would not recommend this company for the following reasons:1. Original appointment was very specific to them on what was needed and to take photos for 3 apartment unit plumbing fixture repairs. One unit had a bathroom tub/shower backup.2. No photos taken, 3 trips later and only 1 unit completed to satisfaction. (Backup) 3. Other faucets unable to find on line with their suppliers and repair 4. Had to find another plumbing company to complete the jobs. 5. Invoicing had to be redone as not in detail of job address for tax purposes 6. Bad communication throughout the project process with their internal customer service. Their technician and project manager ordering parts. 7. For the back up. Did not bring out correct snake on both trips and had to replace lines as too small to break through backup. Costing over $800 for 3 trips just to complete that situation out. 8. Ordered the wrong parts when 2nd trip out since no photos taken to confirm what was needed. Very dissatisfied and will never ask them to work in any of our rental properties again.
Hello my name is Jason. I am a seasoned Construction Worker with 2 college degrees under my belt. One in Electrical Engineering and another in Culinary Arts. I possess an array of skills derived from my higher education, my experience in the Construction Industry and also from Data Networking. I am a master at problem solving and researching so rest assured I know how to get the job DONE!!!!!!
Safest way to ensure that everything is fair is to get it ALL in writing , signed by both parties. Specify each item that needs repair. Also, BUY the paint YOURSELF. That way, there is no incentive to water it down, and you KNOW that you are getting the grade/quality you actually purchased. Don't be penny wise and pound foolish; if you are paying to hire a painter, buy the best paint that you can afford, to ensure maximum life of this home improvement.
to be the devils advocate i have been a building contractor 20 of the last 30 yrs. i do know that if you go to a higher sheen of paint and or darker colors then any imperfections in the walls will show up much more dramatically…therefore the painter or a good drywall finisher is needed to prepare the walls extensively. this could cause more expenses…for it takes a lot of time to prep walls (smooth walls..not textured walls) and this cost has to be absorbed.
Not all people live where they can hire a painting contractor, like you describe. People who live in small towns can only hire painters who have a very small business, and do two or three paint jobs per week. In this case, you do have to be very careful, when you hire a painter, as we have several, in our area, who are out to make a fast buck anyway they can.
As you walk through your lighted rooms (preferably day light) see if the new coat has light spots showing the precious paint. This is call "bleeding through". This means that there's only one coat of paint or the paint was diluted or the trasition of colors were from light to dark (or the other way around) and primer was not use or the painter is inexperienced.
The cost of paint is about 15-25% of the cost of the contract. Mid grade paint costs about $40 per gallon with contractor pricing. If you are painting your home for real estate purposes and you don’t want to spend a lot of money, there is cheaper paint available. Stay away from anything that costs less than $25, you are buying watered down colour that is difficult to use. If you are thinking of using the most expensive paint available, you can spent over $120 per gallon from manufacturers like Farrow & Ball. Whatever you decide, keep in mind that since labour is your biggest expense, why not use the best paint your budget will allow.