The pros were split on this tip. "Masking tape is problematic," says Mark Dixon, a painter in Missoula, Montana, and author of "House Painting Inside and Out" (Taunton Press, 1997). "Paint can bleed behind the tape, or remove the paint it's stuck to." Another problem is bridging. "Latex paints form a skin," says Dixon. "Removing painted tape can tear the skin, resulting in a ragged rather than a sharp line." Lastly, taping takes time. "Learning how to cut in with a brush takes practice, but if you can do it, you'll leave most tapers in the dust," Dixon says. (Cutting in is painting just the surface you want, not the surface adjacent to it — for example, where a wall meets the ceiling.) On the other hand, "If you can't cut in, you can't beat tape," says Span. The pros we spoke with all recommend painter's (blue) tape because it's easier to remove than masking tape. To prevent bleeding, Span uses a putty knife to bed the tape. After letting the paint dry, he scores the edge of the tape line with a utility knife to avoid tearing the paint.
Spray Option – $3,800 to $5,500. This package involves removal and spraying of all the doors, drawers, frames and boxes. It’s a good option for high quality existing kitchen cabinets and it’s the closest you can get to a factory finish. Spraying happens off the site, but on site painting can be arranged if the customer prefers it. We suggest installing new and upgraded hardware.
WOW! I think the guy I hired read this first and I have photos that would make your skin crawl. Bottom line: he got me for $1900.00. Every single thing he painted had to be completely redone....that's when I discovered he did NOT use the colors I picked, he actually used leftover exterior paint from his mother's house! Because I have pets he said things needed to be sealed first and I did agree to that. What I did NOT agree to was using some kind of foul smelling gray stuff ON MY HARDWOOD FLOORS! THEN he painted them BLACK, telling me that all they were good for was covering over with laminate or carpet. He also dripped and tracked paint all over my ceramic tile floors. PLUS left a wet used paint roller in my garden window and had stuff piled in front so I didn't find it until it had dried. I have no idea how much that is going to cost to repair. Then he left without finishing (thank God) but left the "leftover" paint, uncovered, in the rain. Again, hid it so I didn't immediately find it. Obviously we will be going to court but I doubt if I see a penny from him.
"I couldn't be more pleased with this painter! He was extremely curtious, listenened to what I wanted and threw in his suggestions when I needed them. The entire house looks wonderful, I'm so gratful for the way it all turned out. I had many, MANY quotes, not only was his the lowest, but he also guaranteed his work and made sure we were happy with it all. Great company, great guy, great paint job. I couldn't be more pleased!! 😊"
To get basic measurements, measure the length and width of each wall you want to paint in inches. Multiply the length and height together, and divide by 144. This will give you the square footage for each wall. A gallon of paint typically covers around 400 square feet. In some cases, you may need a primer 2 first, then a single coat of paint, meaning that you may need one gallon of primer and one gallon of paint to cover 400 square feet. However, if the wall requires multiple coats, this will increase the total amount of square footage required, and therefore the amount of paint.
The Cutters. Someone with meticulous attention to detail and a steady hand should be assigned the job of "cutting in," or painting a straight edge where needed, such as along a wall where the ceiling does not get painted. Many products are available to assist, but none work as well as a person who's good at doing it freehand. Ensure this person is skilled (ask them to show you). A poor, jagged, wavy or splotched cutting-in job will jump out at you every time you walk by it. Why more than one cutter? This job is nerve-wracking and painful to hands and arms after a few days. You'll want to give this person a break after a few walls.

Paint gets more expensive as you go from flat to gloss. The difference is usually around $1 per gallon per sheen upgrade. Flat is the cheapest, then matte flat or eggshell, satin, semigloss then gloss. Paint also gets much more expensive the darker it gets. A white or neutral paint color can be as much as $20 less expensive than a deep base red or blue.


A fellow (actually lives in the same neighborhood) by the name of Wayne Hickey (843-655-0366) painted the ceilings and most of the walls of our house in February 2017. He got paint all over my light fixtures, all over my trim around the doors, and had visible lap marks everywhere on the walls. He came back and rectified some of the problems, but not all, as I have noticed as I have had time to look more carefully at the work he and his assistant did. His assistant had no idea (not a clue) how to roll paint on a wall or ceiling. Some places were not covered. He said he would pull nails for pictures and then re-insert the nails exactly where they were. This he did not do as he promised. He painted over the nails. His assistant had no idea how to use a paint roller. I have painted all my life, and would have done this work myself, but I just had a full knee replacement and the other knee is in bad shape. I just could not do the work. Wayne is a pleasant and congenial individual, but he can not cut in a ceiling or wall to my satisfaction - not even close. He should have a putty knife and wet cloth with him all the time to correct any paint that might get applied where it shouldn't. That is something I always did as a painter. I would not recommend Wayne to paint anybody's home.

When painting a carpeted room, keep in mind that paint will soak through drop cloths. This is especially true of the cheaper, lightweight cloths. It helps to tape masking paper to all of the base boards before laying the drop cloths. Tuck the edges of the cloth under the paper--this will help keep it clean. You might want to invest in a hand-held masking machine--they make the job go much faster. Even after taking these precautions make sure to clean big drops or spills before they soak through and before you step on them!

"Cutting in is an acquired skill, but it's something you can't do at all with a ratty brush," says Doherty. When cutting in on a wall, he loads his brush and spreads out the excess paint, then works the brush up to the line between wall and ceiling. A brush stroke that's too wide creates a hatband, or smooth brushed band, on the very top of the wall where it meets the ceiling. To avoid this, Dixon recommends rolling first and then cutting in with a brush. "A good roller can get within 1/2 inch of the ceiling," he says. "You'll save time by not brushing more then you have to." When painting baseboards, "a wide taping knife makes a good paint guard," says Span. "Just keep the blade clean to prevent drips from working around the edge of the knife."
You have to start with a perfectly smooth surface to end up with perfectly painted walls or woodwork. One pro tells PM that Sander would be a more fitting job title than Painter since he spends so much time pushing sandpaper. Sanding levels outs spackle or joint-compound patches and flattens ridges around nail holes. Sanding also removes burrs and rough spots in your trim.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
A special thanks to the employees of Warline as they were a very courteous and professional group of young men and women. Not one complaint was received from the owners during the two month process with all owners stating that they were very pleased with the outcome and the professionalism of all involved. The strata council of Hazelmere Village (South Surrey) have no hesitation in recommending Warren Nyline and his company as a painting contractor for your painting needs. A stress free job extremely well done.
After painting the ceiling, work from the top down: Start with the crown molding, then do the walls and then paint the casement molding around the windows and doors. Do baseboard molding last. "Painting the baseboards last keeps dust and grit from traveling off the floor, onto the brush and then up onto the freshly painted casements," explains Weeks.
Sand the trim with a fine-grit sanding sponge. Sponges get into crevices where sandpaper can’t go and let you apply even pressure. Then apply the first coat of paint, let it dry at least 24 hours, lightly sand it again for a completely smooth surface, and apply the second coat. After each sanding, vacuum the trim, then wipe it down with a tack cloth to remove the dust.
The companies with the best paint products are Benjamin Moore, Dunn Edwards, Sherwin Williams, and Vista Paint. As a painter I don't recommend Berh from Home Depot as much because it's quality is just marketing. Flat paint has no sheen and it shows its true color, but is not easy to wash or clean. Satin, eggshell have low sheen and is washable. Semigloss ang glossy has a high sheen and these paints are recommended for bathrooms and kitchen or where there's high humidity and steam.
I was a painting contractor for many years and never asked for a deposit upfront. A good contractor should have great credit with his suppliers and an even better contract if the deal should go south before the job is done. Get to know your customer and explain how each paint covers so they understand fully before you have to apply 3 or 4 coats. If you didn't bid your job right and the client has already signed the contract then that is on you not the client. Yes I haven had to eat the difference but the client was happy and a return customer for years so I made up for it.
The floor and ceiling surfaces cannot be ignored, as they are crucial elements of color combination. Most ceilings are traditionally painted white for a number of reasons — particularly for their ability to keep rooms looking bright and to avoid taking attention away from the walls. Lighter ceiling colors can also help to make a room appear larger and more open.
It’s important to note that complimentary hues work best with each other when they are of the same value. Referencing the provided color wheel, you’ll notice that each pie wedge is segmented into rings of decreasing size. And the value of each hue changes as the rings get smaller. So, if you’ve decided your kitchen needs to be a pure red (the outermost red), then it’s complimentary color is going to be a pure green (opposite & outermost on the ring).
So, you’ve chosen your paint colors (hues & all) with the proper finish for each room of the house. But how do you ensure that moving through each, freshly painted, room won’t make it seem like you changed your mind a few too many times? The answer is easily answered with one word…. Well, two words… baseboards & molding. Though the dominant colors & their respective finishes may vary in each room, you should choose one color & finish for any accent pieces.
We don’t believe in handing our customer a roll of tape and asking them to check for deficiencies. That’s our job and we take it seriously. Our quality control is ongoing and done through every step of the project. Our interior painters are constantly checking their own work and our team leaders conduct a full inspection of the job when it’s completed. Our layers of quality control and inspections mean that when we are done, and you do a final walk through, the only thing you should be seeing is a beautiful paint job.
When hiring a contractor it is always best to hire one who is personally referred to you by someone you trust. Hiring through ads or phone book is hit and miss. Check with your local paints stores, they know the good guys from the bottom feeders. Go to the stores that sell the high quality paints like Benjamin Moore(nonpareil), Pittsburg, Sherwin Williams or Glidden. Don't go the the big box stores for referrals, the people there don't know squat!
Spills and spatters happen, regardless of how careful you are. It’s a lot easier to pre- pare for them than to wipe them out of your carpeting or off your wood floor later. All it takes is canvas drop cloths in your work area (a 4-ft. x 15-ft. cloth costs $15). The thick canvas stays in place, so you don’t need to tape it, and you can use it to cover any surface. Plastic drop cloths are slippery to walk on or set a ladder on and don’t stay in place. Even worse, paint spills on plastic stay wet, and they can end up on your shoes and get tracked through the house. Canvas is slippery on hard floors, so rosin paper ($10 for 400 sq. ft. at home centers) is better over vinyl, tile and hard- wood. Tape the sheets together and to the floor to provide a nonslip surface.
Prime. Dark colors, stains (once sealed), and previously unpainted surfaces (drywall, spackle, etc.) will need a primer coat, usually white. NOTE: most paint stores & home improvement centers will now tint primer (at no charge) to match fairly close to the color of the finished coat, that way two coats of primer need not be applied. Although not all surfaces need a prime coat, skip this step at your peril! Dark colors will likely show through the first -- or even the first couple-- topcoats of paint. Sealants and unpainted surfaces like spackle patches will absorb or repel moisture in a topcoat at a different level than the areas surrounding them. Applying a good primer coat will help even out these differences. Primer equalizes a wall to a uniform surface. It's like erasing a canvas before drawing a new picture. Although some will argue the point, you generally don't need to spend a great deal on primer or buy special primer. A cheap, 5 gallon (18.9 L) bucket of plain, flat white paint will usually do the trick and cover a large area. Give your primer at least 24 hours to dry (follow its instructions) before applying a topcoat.
Modern Masters 1 gal. Brass Metallic Interior Paint Modern Masters 1 gal. Brass Metallic Interior Paint can be used to create a high-end decorative finish in a variety of circumstances. Use it on a small accent piece or large architectural specification. Durable and long lasting for commercial application yet easy enough for do-it-yourself projects. Special formula contains real ...  More + Product Details Close
This is an area that interior painters can easily cut short to save time. Most contracts don't state the extent of the wall repairs included, so it's up to the painter's discretion how much they will do. If it seems like too much work, they'll usually point out the repairs but don't include it in the bid. They'll then ask you if you'd like it fixed after they start your project and let you know how much more it will cost.
Oh, where to begin? Let me start with 'watered down paint'. 25-50% before the material gets to the site? Impossible. You would basically be painting with water at that point. It would be less of a hassle, and cost, to simply use proper material. You would be forced to apply three coats instead of two, as the coverage would be horrible. Whatever cost you think might be saved in materials would be lost in labor.
My wife and I just painted the interior of our house with about 6-8 gallons, of $30+ per gallon (meaning the good stuff, non-diluted) with absolutely fantastic results. However we just paid an average of $5 per gallon. Reason...all big box stores have paint, set aside, that has been mixed but not picked up by the customer. They need to sell it quick and if you're not in a hurry (you know well in advance that a room or two need painting and it's not like the roof leaking and needs an immediate fix) you can go to each store when you need other supplies or food, like Walmart (when convenient, driving 20 miles to each is not worth it) and over the course of a month or two, pick out some very nice colors of quality paint. We found perfect colors...not saying they were our first choice but when we opened the can, very nice and some even better than our original picks. Cost to paint the entire house was about $100, with all materials included, period. We had it on the market for a few months to sell, didn't sell, painted the rooms, got 2 offers the day after we finished, took the best one and never looked back.

To get basic measurements, measure the length and width of each wall you want to paint in inches. Multiply the length and height together, and divide by 144. This will give you the square footage for each wall. A gallon of paint typically covers around 400 square feet. In some cases, you may need a primer 2 first, then a single coat of paint, meaning that you may need one gallon of primer and one gallon of paint to cover 400 square feet. However, if the wall requires multiple coats, this will increase the total amount of square footage required, and therefore the amount of paint.

House Interior Painting Design Co

×